International Interzone 954 Tintable all

Description

International Interzone 954 is a two component, low VOC, high solids, modified epoxy barrier coating designed to give long term protection in a single coat application. Will continue to cure when immersed in water and has excellent cathodic disbondment resistance.

• Pack size: 5 litre and 20 litre units

• Colours: Multiple colour options available

Recommended Uses

Primarily designed for use in offshore splashzone maintenance, where its continued cure under immersed conditions makes it ideal for coping with tidal movements and surges. May be applied to reoxidised and slightly damp surfaces. Interzone 954 has also found extensive use in a number of other corrosive environments including rail cars, pulp and paper plants, chemical plants, jetties and sluice gates.

As part of a non-slip deck system in conjunction with appropriate aggregate.

Surface Preparation

The performance of International Interzone 954 will depend upon the degree of surface preparation. The surface to be coated must be clean and free from contamination. Prior to paint application all surfaces should be assessed and treated in accordance with ISO 8504:2000.

Accumulated dirt and soluble salts must be removed. Dry bristle brushing will normally be adequate for accumulated dirt. Soluble salts should be removed by fresh water washing.
Oil or grease should be removed in accordance with SSPC-SP1 solvent cleaning.

Method of Application

Recommended:

• Airless Spray

• Air Spray (Pressure Pot)

Suitable:

• Brush

• Roller

Please refer to the Data Sheet for additional preparation, application and safety instructions prior to usage.

Systems Compatibility

International Interzone 954 will generally be applied to bare steel prepared by dry abrasive blasting, wet abrasive blasting or ultra high pressure hydroblasting.

Recommended Primers for Interzone 954:

• Intercure 200 epoxy primer

• Intercure 200HS epoxy primer

• Intergard 251 epoxy primer

• Intergard 269 epoxy primer (for underwater use)

• Interline 982 epoxy primer (for underwater use)

• Interzinc 52 epoxy primer

• Interzone 1000 epoxy coating

Recommended Topcoats for Interzone 954:

• Interfine 629HS acrylic finish

• Interfine 878 high solids finish

• Interfine 979 isocyanate-free polysiloxane finish

• Intergard 740 epoxy finish

• Interthane 870 polyurethane finish

• Interthane 990 polyurethane finish

• Interzone 954 epoxy coating

For other suitable primers and topcoats please contact us for technical advice.

Thinner

The recommended thinner for Interzone 954 is International Thinner GTA007. However, thinning is not normally required. Contact us for advice regarding application in extreme conditions.

Maximum recommended thinning 5%. Do not thin more than is allowed by local environmental legislation.

Clean Up

Do not allow material to remain in hoses, gun or spray equipment during work stoppages. Thoroughly flush all equipment with International Thinner GTA822. Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed units.

Clean all equipment immediately after use with International Thinner GTA822. It is good working practice to periodically clean equipment during the course of the working day. Frequency of cleaning will depend upon amount used, temperature and elapsed time, including any delays.

All surplus materials and empty containers should be disposed of in accordance with appropriate regional regulations/legislation.

Safety Precautions

This product is intended for use only by professional applicators in industrial situations in accordance with the advice given on the Data Sheet, the Material Safety Data Sheet and the container(s), and should not be used without reference to the Material Safety Data Sheet (MSDS).

All work involving the application and use of this product should be performed in compliance with all relevant national, Health, Safety and Environmental standards and regulations.

In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation.

Contact Us

For further advice regarding the use of this product, technical support or a quotation please contact us.